people not to do DIY takes for the things so today I'm going to show youhow to make very easy and very beautiful wedding cake topperme don't have wire and crystal beads so it's a simplehard and it's made with 1p supplier that which is about millimeters wind and this 1i used aluminum iron but youcan use copper wire or any silver colored wire Golder anycolor you want and it's basically a heart with anextension stick that plants into the cake so what I'mgoing to do for that is start with my winer and I've cut apiece that's Abboud inches long so it's reallygood to depend on how big you want your hard to be for this one I'm gonna use they can and medium to small size pill bottle tomake the sheep the the round part at the top andall-star obey road four-inches' from one end and I'm gonna hold the pill bottle inplace and I'm gonna actually just twistedaround to make a bit %uh at curve make that you can see making a bit of aKern that's my first kar so there we go likethat and then to twist too bad I'd like tobend it in a way that will have a little loop there and that's gonna fix the liar in placeby me and the beads so we're going to spend it with aroundfires I'm my technique is usually just to hold thewire with the players and then didn't the land like so we've got turning at the heart like that and the same thing take the pill bottlehold it in place and twist the liar around and if you want a nice band I usually gobeyond where I wanna actually have band so itmakes it really wide curved and this one to amendadjusted so it's a little bit past where I i dnt want it to be and so youhave a nice wine hard and then you can kinda bend down the ends and this is where you can I am delightedto see that its a good kinda sheep so I think I'm gonnahave to bow their and what I want to do is I'm gonna bendthe long piece on a bit over raining alike and and then this piece once I've check that its in the position iwon then I'm gonna hold it in place just ended around three times line to me and after that you wanna can't just the in place me to go like that and ifit needs adjusting you can and then I'll just take my flat playersgive it a little pinch not too much because youdon't wanna break the other wire and you can strain at the end and forthe wedding cake I would probably trendiness to aboutseven-and-a-half inches depending on what hate you want K so there's are heart now for the nextpart we're gonna canopy Supplier it's thinner it's about gauge thisone for sure I would use the copper wire because it's more flexible TV getting ontarnished copper wire you can give it a little bit and kind ofhalfway through the wire studded belt
into and we wanna start in the middle of the heart sowe're gonna feed this through that middle at the heart like an and then sticky with a long and inspect you justget them at the way like that and then we'll just twist this issuearound a couple times to hold it in place so that it secured so once we have trees to the wire around a couple of times to thank them then we can start adding our beads me so I've got some crystal beads here I use different sizes to make it lookmore interesting so this one is a better dayeight-millimeter I use anything from four millimeters to heat millimeters they can be round orthey can be kinda all whatever shape you like so I stuck the wire through the bead and now I wanna do a full turn aroundthe wire before I put the next be because that'llhelp to secure it in place we do a full turn around and then I would add my neckspeed and I would probably and a smaller be there yes but a little bit nervous mymeet their %um just turnaround and like I said full turnaround beforeeating unique speed and that way when you get to the end yoube able to adjusted in place and it'll hold inplace now the tricky part is to fix a bean in themiddle here so what I would do for that is I would just bring in around one-time who bring in around a long time and then we're going to move get a bethat we want to put in the middle so could be have brown beat could be more flight be and one just feeding on you mom and I would try and kind of hold itover that little new too so it's centered and then twistedaround a couple at times to hold it in placeand the wires pretty forgiving so if it's not like perfect right awayyou can definitely readjust it once you Peter all on so that should issue the beads centered in the middle and then we're going tokeep going around both sign so now we've come tothe end I've done one sign and twisted the wirearound and no I'm on my other signed and we just have a little bit oven andhear switches get it twisted around the top the state their to sit around a couple a time and themoney clip it very close to the end and now you can kinda just the beads how you like them they could be kindaafter the signed but they can be more on top for the wirewhatever you prefer see getting little twist around andtheir is your finished beaded hard wind kicked up